Fast delivery
Get in as fast as 1 hour
It’s all local
Shop your favorites
Direct chat
Connect with shoppers
About
Details
8 min. set time. 16 hour cure time. Up to 300 PSI strength. Dries dark grey. Bonds to: Aluminum, brass, bronze, copper, iron, stainless steel, & steel. One hardener / One resin. Permatex Cold Weld is a two-part, high strength, cold welding epoxy that can be drilled threaded, machined, filed or painted once fully cured. Has a test-proven shear strength greater than 3,000 PSI after 16 hours. Resistant to shop fluids, including diesel fuel, gasoline, antifreeze, water, oil, transmission fluids, and hydraulic fluids. Temperature Range: -60 degrees F to 300 degrees F continuous, -60 degrees F to 350 degrees F intermittent.
Ingredients
Contains: Limestone (CAS 1317-65-3), Mercaptan Amine (Proprietary), Epoxy Resin (CAS 25068-38-6), Benzyl Alcohol (CAS 100-51-6).
Directions
Directions: 1. For best results: Roughen, remove any grease and oil, clean and dry surfaces to be joined or repaired. 2. Remove tube caps. Pierce end of tubes with the back of cap. 3. Squeeze equal amounts of Resin and Hardener onto a discardable surface. Squeeze with equal pressure from bottom of tubes so diameter of bead is uniform. 4. Mix thoroughly until evenly colored. 5. Apply to surfaces to be joined or repaired. Epoxy starts to set in 8 minutes and reaches usable strength in 16 hours. When storing, clean caps and tube threads. Replace caps to original tube (color coded), or hardening may occur in tube nozzles.
Warnings
Caution: Avoid contact with eyes and prolonged contact with skin. Wear gloves while using. Do not breathe vapors. For eye and skin contact, flush with water for 15 minutes; call a physician. For skin contact, wash thoroughly with soap and water. If swallowed, do not induce vomiting; call a physician. See Safety Data Sheet for complete GHS hazard communication. Keep out of the reach of children. Warning: This product contains chemical(s) known to the State of California to cause cancer, birth defects or other reproductive harm.
About
Details
8 min. set time. 16 hour cure time. Up to 300 PSI strength. Dries dark grey. Bonds to: Aluminum, brass, bronze, copper, iron, stainless steel, & steel. One hardener / One resin. Permatex Cold Weld is a two-part, high strength, cold welding epoxy that can be drilled threaded, machined, filed or painted once fully cured. Has a test-proven shear strength greater than 3,000 PSI after 16 hours. Resistant to shop fluids, including diesel fuel, gasoline, antifreeze, water, oil, transmission fluids, and hydraulic fluids. Temperature Range: -60 degrees F to 300 degrees F continuous, -60 degrees F to 350 degrees F intermittent.
Ingredients
Contains: Limestone (CAS 1317-65-3), Mercaptan Amine (Proprietary), Epoxy Resin (CAS 25068-38-6), Benzyl Alcohol (CAS 100-51-6).
Directions
Directions: 1. For best results: Roughen, remove any grease and oil, clean and dry surfaces to be joined or repaired. 2. Remove tube caps. Pierce end of tubes with the back of cap. 3. Squeeze equal amounts of Resin and Hardener onto a discardable surface. Squeeze with equal pressure from bottom of tubes so diameter of bead is uniform. 4. Mix thoroughly until evenly colored. 5. Apply to surfaces to be joined or repaired. Epoxy starts to set in 8 minutes and reaches usable strength in 16 hours. When storing, clean caps and tube threads. Replace caps to original tube (color coded), or hardening may occur in tube nozzles.
Warnings
Caution: Avoid contact with eyes and prolonged contact with skin. Wear gloves while using. Do not breathe vapors. For eye and skin contact, flush with water for 15 minutes; call a physician. For skin contact, wash thoroughly with soap and water. If swallowed, do not induce vomiting; call a physician. See Safety Data Sheet for complete GHS hazard communication. Keep out of the reach of children. Warning: This product contains chemical(s) known to the State of California to cause cancer, birth defects or other reproductive harm.
Common questions
Learn more about how to place an order here.
Then, when you arrive at the store of your choice, use the Instacart app to notify us. Depending on the store, a shopper or store employee will bring the groceries to your car, or you can pick them up at the designated area.
Learn more about pickup orders here.
- Delivery fees start at $3.99 for same-day orders over $35. Fees vary for one-hour deliveries, club store deliveries, and deliveries under $35.
- Service fees vary and are subject to change based on factors like location and the number and types of items in your cart. Orders containing alcohol have a separate service fee.
- Tipping is optional but encouraged for delivery orders. It's a great way to show your shopper appreciation and recognition for excellent service. 100% of your tip goes directly to the shopper who delivers your order.
With an optional Instacart+ membership, you can get $0 delivery fee on every order over $35 and lower service fees too.
Instacart pickup cost:
- There may be a "pickup fee" (equivalent to a delivery fee for pickup orders) on your pick up order that is typically $1.99 for non-Instacart+ members. Instacart+ membership waives this like it would a delivery fee.
- Pick up orders have no service fees, regardless of non-Instacart+ or Instacart+ membership.
Learn more about Instacart pricing here.
You can set item and delivery instructions in advance, as well as chat directly with your shopper while they shop and deliver your items. You can tell the shopper to:
- Find Best Match: By default, your shopper will use their best judgement to pick a replacement for your item.
- Pick Specific Replacement: You can pick a specific alternative for the shopper to purchase if your first choice is out-of-stock.
- Don't Replace: For items you'd rather not replace, choose "Don't replace" to get a refund if the item is out of stock.
Learn more about instructions for specific items or replacements here.
- Missing items
- Incorrect items
- Damaged items
- Poor replacements
- Early/late orders
If an order never came, or you get someone else's order, you can reach out to Instacart Customer Experience.